Audi A3, A4 & A6 1.9 & 2.0 TDi Rear Crankshaft Oil Seal
Audi A3, A4 & A6 1.9 & 2.0 TDi Rear Crankshaft Oil Seal

Audi A3, A4 & A6 1.9 & 2.0 TDi Rear Crankshaft Oil Seal

Brand: Glaser
Model P77353-11
Availability: 9999
Price: £46.00
Ex Tax: £38.33
Qty:     - OR -   Add to Wish List
Add to Compare

Audi 1.9 & 2.0 TDi

Rear Crankshaft Oil Seal (Gearbox End) with housing

Fits Models: A3, A4, A6

Part Number: P77353-11

OEM Number: 038103171S

Engine Codes: AZV, BKC, BKD, BLB, BLS, BMM, BMN, BNA, BRD, BRE, BRF, BUY, BVA, BVF, BVG, BXE


For 8v & 16v engines
 

PLEASE READ THIS FITMENT GUIDE BEFORE ASSEMBLY! CLICK HERE

WATCH THE VIDEO!!
 

* Important fitting information * 

1. Only remove PTFE oil seals from their protective packaging immediately before installation, to protect them from dust and other contamination. 

2. The sealing lip of PTFE oil seals is protected by a plastic sleeve, which can normally be used as an assembly aid. Therefore, the sleeve should remain in place until the seal has been installed. 
 
3. If the seal is to be installed without the sleeve, use the special tool provided by the manufacturer. 

4. Both the PTFE sealing lip and the shaft surface must be completely dry. Do not use any grease or oil. 
 
5. The shaft may not exhibit any sharp-edged chamfers – if necessary, have the edges removed by an engine expert.
 
6. The shaft surface must be in a perfect condition – also here, possible damage must be repaired by an expert. 
 
7. Position the assembly sleeve with the PTFE oil seal on the shaft. 
 
 8. Make sure that the sealing ring is aligned correctly – the sleeve must be located so that the seal can be pushed onto the shaft smoothly. 
 
 9. Push the sealing ring onto the shaft with an even motion. 
 
10. When replacing, the PTFE lip of the new seal should not run in the same position as the old one. 
 
11. You can now remove the assembly sleeve. 
 
12. Do not start the engine sooner than four hours after installation – this permits the new sealing lip to adapt perfectly to the shaft.


The most frequent cause for failure is damage to the PTFE sealing lip during assembly. If the seal is installed without the help of a sleeve or special tool and is shifted or even turned inside out, reliable sealing will hardly be possible. Similarly, the use of oil or grease – as with classical oil sealing rings – will result in total failure of the PTFE oil seal immediately after installation.
 

Free next day delivery - UK Mainland only

If you require any assistance or would like to ask any questions, please click below

Make Model Engine Years
Audi A3 Diesel - 1.9 1896cc 2003 - 2010
Audi A3 Diesel - 2.0 1968cc 2003 - 2012
Audi A4 Diesel - 2.0 1968cc 2004 - 2008
Audi A6 Diesel - 2.0 1968cc 2004 - 2011
Engine Information
Engine Codes AZV BKC BKD BLB BLS BMM BMN BNA BRD BRE BRF BUY BVA BVF BVG BXE
Engine Size 1896cc 1968cc
Engine Type 4 cylinder 16v Turbo Diesel 4 cylinder 8v Turbo Diesel
OEM Part Number 038103171S

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Copyright 2021 - Lymm Engine Components Ltd.
5 Birch Court, Grosvenor Grange, Warrington. WA1 4GD